Kỹ thuật

Air end repairs

Air end repairs

After air end diagnostics, our engineers estimate the necessary repairs and provide calculation of the repairs and necessary spare parts
Thay lọc dầu cho máy nén khí Kobelco như thế nào?

Thay lọc dầu cho máy nén khí Kobelco như thế nào?

Lọc dầu là bộ phận quan trọng trong máy nén khí, có vai trò lọc sạch các cặn bẩn, bụi trong dầu khi dầu quay về hệ thống khí nén, giúp máy hoạt động ổn định và hiệu quả. Lọc dầu cần phải thay định kỳ. Sau đây, Công ty TNHH Máy và Dịch vụ Kỹ thuật Minh Phú xin chia sẻ hướng dẫn thay lọc dầu cho máy nén khí Kobelco.
Bảo dưỡng máy nén khí Kaeser

Bảo dưỡng máy nén khí Kaeser

Máy nén khí Kaeser là thương hiệu máy nén khí hàng đầu của Cộng hòa Liên Bang Đức với công nghệ cao, hiện đại. Sau đây Minh Phú xin giới thiệu đến bạn đọc những lưu ý trước và trong khi bảo dưỡng, sửa chữa máy nén khí để đảm bảo an toàn và đáp ứng đúng kĩ thuật.
6 Bước bảo dưỡng máy nén khí Hanshin GRH-30A định kì

6 Bước bảo dưỡng máy nén khí Hanshin GRH-30A định kì

Thông thường bảo dưỡng máy nén khí được thực hiện 2 lần một năm, tức là sau 6 tháng vận hành máy. Vậy quy trình bảo dưỡng máy nén khí Hanshin thế nào? Minh Phú sẽ hướng dẫn các bạn qua bài viết sau.

Air end repairs

Thứ sáu - 21/12/2018 22:27
 After air end diagnostics, our engineers estimate the necessary repairs and provide calculation of the repairs and necessary spare parts. Depanding on the air end size, the repairscan be release from some days to some months
thay bi may nen khi micos 37, sua chua may nen khi, bao duong may nen khi truc vit, bao duong may nen khi, sua chua may nen khi, bảo dưỡng máy nén khí, sửa chữa máy nén khí, air compressor repair service, air compressormaintanece service
Air compressor repair Service
Our company repairs the air end of the following manufacturers: ABAC, Dyna, Kobelco, Fusheng, Hitachi, Hanshin, Micos, Swan, Ingersoll Rand, Boge, Atlas Copco, Sullair, Kaeser, Kyungwon, Compair, Puma, Buma, Ceccato, Airman, Quincy, SCR, Mitsui Seiki, Swan, Sung Shin,… 
Possible cases of air end repairs:
 1.Run-out of the shaft seal and sealing rings, and as result, oil leaks. Insufficient quantity of the oil will not cool the air and bearings lubricant enough, and will be the case of equipment break, and as result will not lubrucate of the rotors effective and air overflows from the screw coils, that reduce the performances of the screw compressor.   
 2. Bearing run-out is a reason of changing screw alignment, changing the gaps (increasement and decreasement).
At best, the efficiency will be decrease (in case of the end gap increase), at worst, air end blocks because of welding the rotors to the housing of the screw unit (in case of end gap decrease) and block because of changing the rotors alignment.
3. Burrs on screws.
At first it increase the load on bearings (bearing run-out increasing, power loss), then the open space for the contact is appear occurs the air end block. The similar result can be reached after certain time of noise inside the air end without any reaction from the personnel side.
cach thay vong bi may nen khi,bao duong may nen khi, sua chua may nen khi, bảo dưỡng máy nén khí, sửa chữa máy nén khí, air compressor repair service, air compressormaintanece service
Air end repairs include:
1. Diagnostics: disassembly, revision and assembly the air end.
2. Bearings replacement (we use bearings the best world bearings manufacturers).
3. Rotor surface recovery (if necessary).
4. Housing geometry recovery (if necessary).
5. Air end shaft seal kit replacement.
6. The optimal gap adjustment and rotor alignment, gaps regulation:
Gap and rotor alignment adjustment is released with using special tool, due to the highest efficiency of the air end and long lifetime of the  unit is providing.  The gaps adjustment are in certain ranges, which provides high efficiency.If during compressor operation the gaps (for example, end gaps) will be adjust less than minimum value of the range, rotors heat, metal expands and it is a reason the rotor and housing contact. As rotation speed is high, shortly metal weld.
Then the screw unit can be just utilize. If the gaps are highter than maxumum value of the range, efficiency decreases because of air-oil mixture leaks,  as well as parameters of the cooling element and rotor lubricant are changed, that prevent  to decrease the air end lifetime.
We provide warranty terms for repaired air end.
Please send us your requests to our e-mail address:
  info.mipuco@gmail.com or contacts us +84 46294 82 82                                                                                               
  Mr : Phu Nguyen
Air end repairs, thay bi đầu nén máy nén khí, thay bi may nen khi, Bảo dưỡng máy nén khí, Minh Phu's air compressor repair Service,

Tổng số điểm của bài viết là: 0 trong 0 đánh giá

Click để đánh giá bài viết